Sun v880上安装emulex HBA，配置Storage Node详细步骤
时间:2008-01-16 13:33:18 来源: 作者:
|
时间：2005-3-4 任务：在Sun v880上加装Emulex LP9002L-F2光纤卡，用来识别P4000磁带库及带机 实施步聚： 1. 关闭v880上的所有应用 2. 关闭系统，切断电源 3. 安装HBA卡到PCI槽 4. 开机，正常启动Solaris系统 5. 以root用户登录到系统，安装lpfc.1驱动程序包，pkgadd ?Cd ./ lpfc.1 6. 修改/kernel/drv/st.conf，增加target数量及lun数量，st.conf如下： # # Copyright (c) 1995-2000 by Sun Microsystems, Inc. # All rights reserved. # # #pragma ident "@(#)st.conf 1.31 00/08/24 SMI" # # This file contains configuration entries for both officially supported # devices of Sun Microsystems and many 3rd party devices. # # The officially supported devices are : # # "ARCHIVE Python 28388" Note 1 # "ARCHIVE Python 28454" Note 1 # "ARCHIVE Python 29279" Note 1 # "ARCHIVE VIPER 150" Note 1 # "EXABYTE EXB-8200" Note 1 # "EXABYTE EXB-8500" Note 1 # "EXABYTE EXB-8505" Note 1 # "EXABYTE EXB-8900" Note 1 # "HP 88780" Note 1 # "HP C5683A" Note 1 # "HP C5713A" Note 1 # "Quantum DLT4000" Note 1 # "Quantum DLT7000" Note 1 # "Quantum DLT8000" Note 1 # "STK 9840" Note 1 # "SUN DLT4000" Note 1 # "SUN DLT4700" Note 1 # "SUN DLT7000" Note 1 # "TANDBERG SLR5" Note 1 # "TANDBERG TDC 4200" Note 1 # "TANDBERGMLR1" Note 1 # "TANDBERGMLR3" Note 1 # # The unsupported devices are : # # "Emulex MTO2" Note 1 # "ANRITSU DMT2120" Note 1 # "ARCHIVE Python 04106" Note 1 # "ARCHIVE VIPER 255" Note 1 # "DEC DLT2" # "DEC TZ87" # "EXABYTE EXB-2501" Note 1 # "EXABYTE EXB-4200c" Note 1 # "EXABYTE EXB8500C" # "FUJITSU M1016B M2483B" # "FUJITSU M248" # "HP C1533A" Note 1 # "HP C1553A " # "HP C1537A" Note 1 # "HP C1557A" Note 1 # "HP HP35470A" Note 1 # "HP HP35480A" Note 1 # "IBM 03490" # "IBM 9348" # "KENNEDY" Note 1 # "LMS" Note 1 # "M4 DATA 123107 SCSI" Note 1 # "Metrum" # "R-BYTE RB100" # "Seagate STT20000N" Note 1 # "SONY SDT-5000" Note 1 # "SONY SDT-5200" Note 1 # "STK 9490" # "STK 4280" # "STK" Note 1 # "TANDBERG 4100" Note 1 # "TANDBERG 4200" Note 1 # "TELEX" # "WANGTEK 51000 SCSI" # "WANGTEK 5150ES" Note 1 # "WANGTEK 5525ES SCSI" Note 1 # "WANGTEK 6130-HS" Note 1 # "WangDAT Model 2600" Note 1 # "WangDAT Model 3400" Note 1 # "WangDAT" Note 1 # " 76 00" Note 1 # # Notes # ----- # 1 Drive is configured automatically - no entry is needed in st.conf. # # The 3rd party devices do apparently work with the configurations listed. # All the entries have been taken from the net and probably have worked in # the past, but have not been tested by Sun Microsystems. Use these entries # as your starting point for generating your configuration entries. # # tape-config-list= #"HP Ultrium 2-SCSI", "HP LTO Ultrium Generation 2", "Class_HP460", #"Emulex MTO2", "Emulex MT02 QIC-11/QIC-24", "MT02", #"ANRITSU DMT2120", "Unisys 1/2" Reel", "ANRITSU", #"ARCHIVE Python 04106", "Seagate Scorpion 24 DDS3 DAT", "ARCH_04106", #"ARCHIVE Python 28454", "Archive Python 4mm Helical Scan", "ARCH_Python", #"ARCHIVE Python 29279", "Archive Python 4mm DAT Stacker", "ARCH_Python", #"ARCHIVE Python 28388", "Archive/Conner CTDX004 4mm DAT", "Conner2-DAT", #"ARCHIVE VIPER 150", "Archive QIC-150", "QIC150", #"ARCHIVE VIPER 255", "Archive QIC-525", "QIC150", #"DEC DLT2", "DEC DLT", "DLT2", #"DEC TZ87", "DEC DLT", "DLT2", #"EXABYTE EXB-2501", "Exabyte EXB-2501 QIC", "EXB-2501", #"EXABYTE EXB-4200c", "Exabyte 4mm Helical Scan", "Exa4200c", #"EXABYTE EXB-8200", "Exabyte EXB-8200 8mm Helical Scan","EXB-8200", #"EXABYTE EXB-8500", "Exabyte EXB-8500 8mm Helical Scan","EXB-850X", #"EXABYTE EXB-8505", "Exabyte EXB-8505 8mm Helical Scan","EXB-850X", #"EXABYTE EXB8500C", "Exabyte 8500C 8mm Helical Scan", "EXB-850X", #"FUJITSU M1016B M2483B", "Fujitsu 1/2" Cartridge", "Fujitsu_comp", #"FUJITSU M248", "Fujitsu 1/2" Cartridge", "Fujitsu_m248x", #"HP 88780", "HP-88780 1/2" Reel", "HP_half", #"HP C1533A", "HP DDS2 4mm DAT loader", "HP_DAT", #"HP C1553A ", "HP C1553A 4mm DAT", "HP_DAT", #"HP C1537A", "HP DDS-3 4mm DAT ", "HP_DAT_3", #"HP C1557A", "HP DDS-3 4mm DAT loader", "HP_DAT_3", #"HP HP35470A", "HP 35470A 4mm DAT", "HP_DAT", #"HP HP35480A", "HP 35480A 4mm DAT", "HP_DAT", #"IBM 03490", "IBM 3490E 1/2" Cartridge", "CLASS_3490", #"IBM 9348", "STK 4220 1/2" Cartridge", "C3490", #"KENNEDY", "Kennedy 1/2" Reel", "KENNEDY", #"LMS", "CDC 1/2" Cartridge", "LMS", #"M4 DATA 123107 SCSI", "M4-Data 1/2" Reel", "M4_DATA", #"Metrum", "Metrum VHS Cartridge", "MetD", #"QUANTUM DLT7000", "Quantum DLT7000", "DLT7k-data", #"SUN DLT7000", "Sun DLT7000", "DLT7k-data", #"Quantum DLT4000", "Quantum DLT4000", "DLT-data", #"SUN DLT4000", "DLT4000", "DLT-data", #"SUN DLT4700", "DLT4700 Library", "DLT-data", #"R-BYTE RB100", "R-Byte Whozits", "DAT", #"Seagate STT20000N", "Seagate Hornet NS20 Travan", "NS20", #"SONY SDT-5000", "SONY 4mm DAT", "DAT", #"SONY SDT-5200", "SONY 4mm DAT", "DAT", #"STK 9490", "STK 9490 1/2" Cartridge", "CLASS_3490", #"STK 4280", "STK 4280 1/2" Cartridge", "C3490", #"STK", "STK 1/2" Cartridge", "CLASS_3490", #"TANDBERG 4100", "Tandberg 4100 QIC", "TAND_4100_QIC", #"TANDBERG 4200", "Tandberg 4200 QIC", "TAND_4200_QIC", #"TANDBERG TDC 4200", "Tandberg QIC 2.5 Gig Tape Drive", "TANDB-2_5G", #"TANDBERG SLR5", "Tandberg 8 Gig QIC", "TAND-8G-VAR", #"TANDBERGMLR1", "Tandberg MLR1 QIC", "TANDBERG_MLR1", #"TANDBERGMLR3", "Tandberg 50 Gig QIC", "TAND-50G-VAR", #"TELEX", "STK 4220 1/2" Cartridge", "C3490", #"WANGTEK 51000 SCSI", "Wangtek 1.2GB QIC", "WtQIC", #"WANGTEK 5150ES", "Wangtek QIC-150", "WANGTEK_QC150", #"WANGTEK 5525ES SCSI", "Wangtek 525MB QIC", "WtQIC", #"WANGTEK 6130-HS", "Wangtek 4mm Helical Scan", "WANGTEK_6130", #"WangDAT Model 2600", "WangDAT 4mm DAT", "WangDAT", #"WangDAT Model 3400", "WangDAT 4mm DAT", "WangDAT", #"WangDAT", "Wang DAT 3.81 Helical Scan", "WangDAT", #" 76 00", "Fujitsu 1/2" Cartridge", "Fujitsu_half"; #ANRITSU = 1, 0x25, 0, 0x0041D, 4, 0x00, 0x02, 0x03, 0x03, 1; #ARCH_04106 = 1, 0x2C, 0, 0x09639, 4, 0x00, 0x8C, 0x8C, 0x8C, 3; #ARCH_Python = 1, 0x2C, 0, 0x0DE39, 4, 0x00, 0x8C, 0x8C, 0x8C, 3; #CLASS_3490 = 1, 0x24, 0, 0x1C43D, 4, 0x00, 0x00, 0x00, 0x00, 0; #C3490 = 1, 0x24, 0, 0x1C43D, 4, 0x00, 0x00, 0x00, 0x01, 2; #Conner2-DAT = 1, 0x2C, 0, 0x0DE39, 4, 0x00, 0x00, 0x00, 0x00, 0; #DAT = 1, 0x34, 0, 0x00439, 4, 0x00, 0x00, 0x00, 0x00, 0; #DLT2 = 1, 0x38, 0, 0x0D639, 4, 0x17, 0x18, 0x80, 0x81, 2; #DLT-data = 1, 0x38, 0, 0x0D639, 4, 0x80, 0x81, 0x82, 0x83, 2; #DLT7k-data = 1, 0x38, 0, 0x0D639, 4, 0x82, 0x83, 0x84, 0x85, 2; #EXB-2501 = 1, 0x28, 1024, 0x00442, 4, 0x00, 0x00, 0x00, 0x00, 0; #EXB-8200 = 1, 0x28, 0, 0x08C79, 4, 0x00, 0x00, 0x00, 0x00, 0; #EXB-850X = 1, 0x29, 0, 0x0CE39, 4, 0x14, 0x15, 0x8C, 0x8C, 1; #Exa4200c = 1, 0x34, 0, 0x01639, 4, 0x63, 0x00, 0x00, 0x00, 1; #Fujitsu_comp = 1, 0x21, 0, 0x18639, 4, 0x00, 0x00, 0x00, 0x09, 1; #Fujitsu_half = 1, 0x21, 0, 0x0063B, 4, 0x00, 0x00, 0x00, 0x00, 0; #Fujitsu_m248x = 1, 0x21, 0, 0x0C639, 4, 0x00, 0x00, 0x00, 0x00, 0; #HP_DAT = 1, 0x34, 0, 0x19679, 4, 0x00, 0x00, 0x00, 0x00, 0; #HP_DAT_3 = 1, 0x34, 0, 0x09639, 4, 0x00, 0x8C, 0x8C, 0x8C, 1; #HP_half = 1, 0x23, 0, 0x0041D, 4, 0x01, 0x02, 0x03, 0xC3, 1; #KENNEDY = 1, 0x22, 0, 0x0041D, 4, 0x01, 0x02, 0x03, 0x03, 1; #LMS = 1, 0x20, 0, 0x0066B, 4, 0x00, 0x00, 0x00, 0x00, 0; #M4_DATA = 1, 0x27, 0, 0x0049D, 4, 0x01, 0x02, 0x06, 0x06, 1; #MT02 = 1, 0x14, 512, 0x00202, 4, 0x84, 0x05, 0x05, 0x05, 1; #MetD = 1, 0x36, 0, 0x01639, 4, 0x00, 0x00, 0x00, 0x00, 0; #NS20 = 1, 0x32, 512, 0x0C40A, 4, 0x00, 0x00, 0x00, 0x00, 0; #QIC150 = 1, 0x15, 512, 0x00642, 4, 0x00, 0x00, 0x00, 0x00, 0; #TANDB-2_5G = 1, 0x32, 0, 0x0D67B, 4, 0x00, 0x00, 0x00, 0x00, 0; #TAND-8G-VAR = 1, 0x37, 0, 0x0963B, 4, 0xA0, 0xD0, 0xD0, 0xD0, 3; #TANDBERG_MLR1 = 1, 0x32, 512, 0x0463A, 4, 0x00, 0x00, 0x00, 0x00, 0; #TAND-50G-VAR = 1, 0x37, 0, 0x0963B, 4, 0xA0, 0xD0, 0xD0, 0xD0, 3; #TAND_4100_QIC = 1, 0x32, 512, 0x0463A, 4, 0x00, 0x00, 0x00, 0x00, 0; #TAND_4200_QIC = 1, 0x32, 512, 0x0463A, 4, 0x00, 0x00, 0x00, 0x00, 0; #WANGTEK_6130 = 1, 0x2A, 0, 0x00659, 4, 0x00, 0x00, 0x00, 0x00, 0; #WANGTEK_QC150 = 1, 0x16, 512, 0x00642, 4, 0x00, 0x00, 0x00, 0x00, 0; #WangDAT = 1, 0x2B, 0, 0x00659, 4, 0x00, 0x00, 0x00, 0x00, 0; #WangDAT = 1, 0x34, 0, 0x00679, 4, 0x00, 0x00, 0x00, 0x00, 0; #WtQIC = 1, 0x32, 512, 0x0467A, 4, 0x00, 0x00, 0x00, 0x00, 0; #CLASS_HP460 = 2, 0x3b, 0, 0x18659, 1, 0x42, 0x42, 0x42, 0x42, 0; # name="st" class="scsi" target=0 lun=0; name="st" class="scsi" target=1 lun=0; name="st" class="scsi" target=2 lun=0; name="st" class="scsi" target=3 lun=0; name="st" class="scsi" target=4 lun=0; name="st" class="scsi" target=5 lun=0; name="st" class="scsi" target=6 lun=0; # #In case there are wide tape drives, one can use these targets # name="st" class="scsi" target=8 lun=0; name="st" class="scsi" target=9 lun=0; name="st" class="scsi" target=10 lun=0; name="st" class="scsi" target=11 lun=0; name="st" class="scsi" target=12 lun=0; name="st" class="scsi" target=13 lun=0; name="st" class="scsi" target=14 lun=0; name="st" class="scsi" target=15 lun=0; name="st" class="scsi" target=0 lun=1; name="st" class="scsi" target=1 lun=1; name="st" class="scsi" target=2 lun=1; name="st" class="scsi" target=3 lun=1; name="st" class="scsi" target=4 lun=1; name="st" class="scsi" target=5 lun=1; name="st" class="scsi" target=6 lun=1; name="st" class="scsi" target=8 lun=1; name="st" class="scsi" target=9 lun=1; name="st" class="scsi" target=10 lun=1; name="st" class="scsi" target=11 lun=1; name="st" class="scsi" target=12 lun=1; name="st" class="scsi" target=13 lun=1; name="st" class="scsi" target=14 lun=1; name="st" class="scsi" target=15 lun=1; name="st" class="scsi" target=0 lun=2; name="st" class="scsi" target=1 lun=2; name="st" class="scsi" target=2 lun=2; name="st" class="scsi" target=3 lun=2; name="st" class="scsi" target=4 lun=2; name="st" class="scsi" target=5 lun=2; name="st" class="scsi" target=6 lun=2; name="st" class="scsi" target=8 lun=2; name="st" class="scsi" target=9 lun=2; name="st" class="scsi" target=10 lun=2; name="st" class="scsi" target=11 lun=2; name="st" class="scsi" target=12 lun=2; name="st" class="scsi" target=13 lun=2; name="st" class="scsi" target=14 lun=2; name="st" class="scsi" target=15 lun=2; name="st" class="scsi" target=0 lun=3; name="st" class="scsi" target=1 lun=3; name="st" class="scsi" target=2 lun=3; name="st" class="scsi" target=3 lun=3; name="st" class="scsi" target=4 lun=3; name="st" class="scsi" target=5 lun=3; name="st" class="scsi" target=6 lun=3; name="st" class="scsi" target=8 lun=3; name="st" class="scsi" target=9 lun=3; name="st" class="scsi" target=10 lun=3; name="st" class="scsi" target=11 lun=3; name="st" class="scsi" target=12 lun=3; name="st" class="scsi" target=13 lun=3; name="st" class="scsi" target=14 lun=3; name="st" class="scsi" target=15 lun=3; name="st" class="scsi" target=0 lun=4; name="st" class="scsi" target=1 lun=4; name="st" class="scsi" target=2 lun=4; name="st" class="scsi" target=3 lun=4; name="st" class="scsi" target=4 lun=4; name="st" class="scsi" target=5 lun=4; name="st" class="scsi" target=6 lun=4; name="st" class="scsi" target=8 lun=4; name="st" class="scsi" target=9 lun=4; name="st" class="scsi" target=10 lun=4; name="st" class="scsi" target=11 lun=4; name="st" class="scsi" target=12 lun=4; name="st" class="scsi" target=13 lun=4; name="st" class="scsi" target=14 lun=4; name="st" class="scsi" target=15 lun=4; name="st" class="scsi" target=0 lun=5; name="st" class="scsi" target=1 lun=5; name="st" class="scsi" target=2 lun=5; name="st" class="scsi" target=3 lun=5; name="st" class="scsi" target=4 lun=5; name="st" class="scsi" target=5 lun=5; name="st" class="scsi" target=6 lun=5; name="st" class="scsi" target=8 lun=5; name="st" class="scsi" target=9 lun=5; name="st" class="scsi" target=10 lun=5; name="st" class="scsi" target=11 lun=5; name="st" class="scsi" target=12 lun=5; name="st" class="scsi" target=13 lun=5; name="st" class="scsi" target=14 lun=5; name="st" class="scsi" target=15 lun=5; # This line adds support for Fibre Channel Tapes name="st" parent="fp" target=0; 7. 重启主机：shutdown ?Ci6 g0 ?Cy，或通过使用下列命令配置磁带设备(可以不重启) # update_drv ?Cf st （使修改后的st.conf生效，仅对Solaris 9有效） # modinfo | grep st （确认st被加载） # modinfo | grep lpfc （确认lpfc被加载） 8. ls /dev/rmt （确认磁带机设备已经生成），如果没有，再执行一次devfsadm。 9. inquire （应该可以看到机械手和磁带库上的磁带机） # inquire |grep Ultrium scsidev@3.0.1:HP Ultrium 2-SCSI F49Z|Tape, /dev/rmt/0cbn ATNN:HP Ultrium 2-SCSI HUL3C00118 scsidev@3.0.2:HP Ultrium 2-SCSI F49Z|Tape, /dev/rmt/1cbn ATNN:HP Ultrium 2-SCSI HUL3C00096 scsidev@3.0.3:HP Ultrium 2-SCSI F49Z|Tape, /dev/rmt/2cbn ATNN:HP Ultrium 2-SCSI HUL3C00078 scsidev@3.0.4:HP Ultrium 2-SCSI F49Z|Tape, /dev/rmt/3cbn ATNN:HP Ultrium 2-SCSI HUL4C02062 10. 使用jbedit ?Ca添加Storage Node。 如果有任何问题，欢迎大家一起讨论。 星海夜航 回复于：2005-03-05 19:14:45 和带库及带机是直连得还是通过san连接得? long_man 回复于：2005-03-06 12:52:05 st.conf ??? sd.conf lpfc.conf 的automap, linkspeed, toplogy 也是需要确认的吧。 david5337 回复于：2005-03-07 10:35:27 楼主辛苦了，很详细的资料！ 可以再讨论以完善的更详细一些！ sonorous 回复于：2005-03-07 16:42:46 引用：原帖由 "星海夜航"]和带库及带机是直连得还是通过san连接得? 发表： 是的，通过FC交换机连的 melonm 回复于：2005-03-08 10:31:30 磁盘设备用sd.conf，磁带设备用st.conf． long_man 回复于：2005-03-08 10:40:33 哦，谢了。。 |
 |
原文链接：http://bbs.chinaunix.net/viewthread.php?tid=505616 转载请注明作者名及原文出处 |
上一篇： 交换机zonging划分问题 不会
下一篇： veritas远程安装遇到的问题
文章评论
共有 位网友发表了评论 查看完整内容